Jedes Modul umfasst 3 ECTS. Sie wählen insgesamt 10 Module/30 ECTS in den folgenden Modulkategorien:
- 12-15 ECTS in Technisch-wissenschaftlichen Modulen (TSM)
TSM-Module vermitteln Ihnen profilspezifische Fachkompetenz und ergänzen die dezentralen Vertiefungsmodule. - 9-12 ECTS in Erweiterten theoretischen Grundlagen (FTP)
FTP-Module behandeln theoretische Grundlagen wie die höhere Mathematik, Physik, Informationstheorie, Chemie usw. Sie erweitern Ihre abstrakte, wissenschaftliche Tiefe und tragen dazu bei, den für die Innovation wichtigen Bogen zwischen Abstraktion und Anwendung spannen zu können. - 6-9 ECTS in Kontextmodulen (CM)
CM-Module vermitteln Ihnen Zusatzkompetenzen aus Bereichen wie Technologiemanagement, Betriebswirtschaft, Kommunikation, Projektmanagement, Patentrecht, Vertragsrecht usw.
In der Modulbeschreibung (siehe: Herunterladen der vollständigen Modulbeschreibung) finden Sie die kompletten Sprachangaben je Modul, unterteilt in die folgenden Kategorien:
- Unterricht
- Dokumentation
- Prüfung
The course starts with an overview of classical engineering physics with special emphasis of balance and constitutive equations (i.e., continuity equations and material laws). The basic concepts of vector analysis are applied to electrodynamics, various transport phenomena, mechanical elasticity and piezo-electric effects. The concept of tensors enables the description of important anisotropic effects of solid state physics. These effects are present in crystals as well as in layered material systems, which are more and more used in modern technology. The given overview facilitates the student’s understanding and application of numerical simulation methods (e.g., FEA, multiphysics).
Eintrittskompetenzen
- Physics, analysis, linear algebra at Bachelor’s level ,
- The mathematical prerequisites are covered by the chapter 7-9 of [4]. The summaries of these chapters are in the appendix of this document.
Lernziele
- Students are familiar with the most important basic laws of engineering physics for isotropic materials in general view form, recognize analogies between different application areas and exploit these for analyzing systems
- Students know about the generalization of the laws for anisotropic materials and can interpret these, especially with regard to application in numerical simulation
- Students master vector analysis and the algebra of tensors together with the standard notation conventions
- Students understand the basics of electrodynamics and transport phenomena for anisotropic systems
- Students understand mechanical elasticity with 3D strain and stress states and are familiar with the material laws in general form for isotropic and anisotropic bodies
- Students understand the piezo-electric effect and its applications in engineering (sensors and actuators)
Modulinhalt
- Recapitulation of isotropic material laws (Ohm, Hook, electric polarization, heat conduction)
- Introduction to vector and tensor calculation: scalar, vectorial and tensorial parameters, tensor algebra,
- Transformation behavior of vectors and tensors
- Hands-on calculation of vector analysis and tensoralgebra: electrodynamics and anisotropic transport phenomena
- Elasticity theory with emphasis on 3D stress states
- Piezo-effect: physical fundamentals
| Week | Subject |
| MW1 | Introduction, motivation, repetition of fundamental physical laws from engineering physics |
| MW2 | Scalars, vectors, divergence, gradient, curl |
| MW3 | Integral theorems and applications of vector analysis in physics |
| MW4 | Maxwell I: Electro- and magnetostatics |
| MW5 | Fundamental mathematical properties of tensors, transformations of tensors |
| MW6 | Transport phenomena, Ohm’s law, heat conduction and diffusion |
| MW7 | Elasticity: stress and distortion tensor, thermal expansion |
| MW8 | Elasticity: Hooke’s law, tensors of the fourth rank, engineering diagram |
| MW9 | Elasticity: 3D stress and distortion states |
| MW10 | Elasticity: 3D stress and distortion states |
| MW11 | Reserve |
| MW12 | Maxwell II: Electrodynamics |
| MW13 | Maxwell III: Waves, Maxwell |
| MW14 | Piezoelectricity |
Lehr- und Lernmethoden
Frontal teaching (approx. 60 %)
Presentation and discussion of case studies and problems, individual problem solving (approx. 40 %)
Bibliografie
[1] R.E. Newham, Properties of Materials, Oxford, 2005
[2] J.F. Nye, Physical Properties of Crystals, Oxford Science Publication, 2004
[3] J.Tichy, Fundamentals of Piezoelectric Sensorics, Springer 2010
[4] E. Kreszig, Advanced Engineering Mathematics, 10th edition, Wiley, 2011
Vollständige Modulbeschreibung herunterladen
Zurück